Search Results

This SAE Recommended Practice is intended for all vehicle hydraulic brake hoses. It is an accelerated test which is intended to provide the user with a method of comparing the ability of hydraulic brake hose designs to retard the ingress of moisture into brake fluid. This document specifies a laboratory performance requirement. ASTM D 1364 interlaboratory reproducibility and correlation of data have not been defined, nor has correlation been established between field vehicle brake fluid moisture content and data obtained by this document.

This SAE Information Report is the listing of recommendations for the proper packaging, storage, and shelf life limitations of new and unused hydraulic brake hose assemblies. The document embodies the testing, analysis, and experience of many users and manufacturers. Where specific manufacturer's recommendations are made, those recommendations shall supersede the recommendations of this document. This document describes the successful procedures and practices associated with brake hose assemblies usage by a wide cross section of manufacturers and users over several years. The practices are expected to be applicable to all brake hose assemblies which qualify under SAE J1401.

This document covers two types of hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications as flexible connections within the temperature range of −40 °C to +120 °C (−40 °F to +250 °F) average, and 135 °C (275 °F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Type 1 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure. Type 2 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure.

This specification covers two types of hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications as flexible connections within the temperature range of –40 to +121 C (–40 to +250 F) average, + 149 C (+ 300 F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Type 1 hose shall be suitable for 1500 psi maximum working pressure. Type 2 hose shall be suitable for 1300 psi maximum working pressure.

This document covers two types of hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications as flexible connections within the temperature range of -40 °C to +120 °C (-40 °F to +250 °F) average, and 135 °C (275 °F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Type 1 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure. Type 2 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure.

This document covers two types of hose fabricated from fabric braid and synthetic rubber, assembled with end fittings for use in automotive power steering applications as flexible connections within the temperature range of −40 °C to +120 °C (−40 °F to +250 °F) average, and 135 °C (275 °F) maximum peaks. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsations is required. Type 1 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure. Type 2 hose shall be suitable for 10.3 MPa (1500 psi) maximum working pressure.

This SAE Recommended Practice covers the application of hydraulic brake hose (as defined by current issue of SAE J1401) as used to provide a flexible hydraulic connection between wheel end or axle brake system components on motor vehicles. The purpose of this document is to outline design, operating, and service factors in routing a hydraulic brake hose assembly to a vehicle. It is intended to serve as a recommended practice for original equipment manufacturers. Vehicle design circumstances may exist that prevent strict adherence to this document. Any deviations should have the concurrence of all engineering functions involved.

This SAE Recommended Practice covers the application of hydraulic brake hose (as defined by current issue of SAE J1401) as used to provide a flexible hydraulic connection between wheel end or axle brake system components on motor vehicles.

This SAE Standard documents dimensional metric specifications for hydraulic brake system tubing with flared ends, threaded ports, and male tube nuts for the interconnection of major components in automotive hydraulic brake systems. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices), that are intended to be functionally compatible with International Organization for Standardization Specification, ISO 4038. Some applications may require sizes of forms other than those shown herein, and this document does not preclude such other details when they are required.

This recommended practice documents dimensional metric specifications for hydraulic brake system tubing with flared ends, threaded ports, and male tube nuts for the interconnection of major components in automotive hydraulic brake systems. The purpose of this document is to recommend preferred metrically dimensioned components (including alternative choices), that are intended to be functionally compatible with International Organization for Standardization Specification, ISO 4038-1977 (E). Some applications may require sizes or forms other than those shown herein, and this document does not preclude such other details when they are required.

This SAE Standard covers hose fabricated from textile reinforcement and synthetic rubber, assembled with clamps and/or end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of −40 to +150 °C (−40 to +302 °F) maximum and 1.21 MPa (175 psi) maximum working pressure. This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering gear back to the pump/reservoir.

This SAE Standard covers hose fabricated from textile reinforcement and synthetic rubber, assembled with clamps and/or end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of −40 to +150 °C (−40 to +302 °F) maximum and 1.21 MPa (175 psi) maximum working pressure. This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering gear back to the pump/reservoir.

This SAE Standard covers two types of hose fabricated from textile reinforcement and synthetic rubber, assembled with end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of −40 to +150 °C (−40 to +302 °F) maximum and 10.3 MPa (1500 psi) maximum working pressure. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsation is required. Class A hose has a nominal OD of 19.84 mm (0.781 in). Class B hose is a lightweight hose with a nominal OD of 17.91 mm (0.705 in). This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering pump to the steering gear.

This SAE Standard covers two types of hose fabricated from textile reinforcement and synthetic rubber, assembled with end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of -40 to +150 °C (-40 to +302 °F) maximum and 10.3 MPa (1500 psi) maximum working pressure. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsation is required. Class A hose has a nominal OD of 19.84 mm (0.781 in). Class B hose is a lightweight hose with a nominal OD of 17.91 mm (0.705 in). This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering pump to the steering gear.

This SAE Standard covers two types of hose fabricated from textile reinforcement and synthetic rubber, assembled with end fittings for use in high-temperature automotive power steering applications as flexible connections within the temperature range of −40 to +150 °C (−40 to +302 °F) maximum and 10.3 MPa (1500 psi) maximum working pressure. These hoses are intended for use in applications where reduction in amplitude of pump pressure pulsation is required. Class A hose has a nominal OD of 19.84 mm (0.781 in). Class B hose is a lightweight hose with a nominal OD of 17.91 mm (0.705 in). This specification defines the minimum performance levels of a flexible connector in the hydraulic steering system to convey power steering fluid from the steering pump to the steering gear.

This SAE Standard covers molded rubber boots used on disc brake pistons to prevent the entrance of dirt and moisture which could cause corrosion and otherwise impair caliper operation. The specification includes performance tests of brake piston boots of both plain and insert types under specified conditions and does not include requirements relating to chemical composition or physical properties of the rubber compound. Further, it does not cover the strength of the adhesion of rubber to the insert material where an insert is used. The rubber material used in these boots is classified as suitable for operating in a temperature range of −40 to + 120 °C ± 2 °C (−40 to + 248 °F ± 3.6 °F).

This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of -40 °C to +120 °C (-40 °F to 250 °F) average and 135 °C (275 °F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.

This document covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of -40°C (-40°F) to +121°C (+250°F) average, 149°C (300°F) maximum peaks. Hose assemblies shall be suitable for 250 psi maximum working pressure with end fittings and 100 psi maximum working pressure with user applied clamps.

This specification covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of –40 C ( – 40 F) to +121 C ( + 250 F) average, 149 C (300 F) maximum peaks. Hose assemblies shall be suitable for 250 psi maximum working pressure with end fittings and 100 psi maximum working pressure with user applied clamps.

This SAE Standard covers hose fabricated from fabric braid and synthetic rubber, assembled with end fittings or user applied clamps for use in automotive power steering applications as flexible connections within the temperature range of –40 °C to +120 °C (–40 °F to 250 °F) average and 135 °C (275 °F) maximum peaks. Hose assemblies shall be suitable for 1.72 MPa (250 psi) maximum working pressure with end fittings and 0.69 MPa (100 psi) maximum working pressure with user applied clamps.